PATINA GREEN PAINT ENAMEL HOW TO
PATINA GREEN PAINT ENAMEL FULL

Bright whites may require additional coats over dark existing finishes. Some colors made in a clear base require additional coats for coverage due to their lower hide quality, e.g., reds, deep blues and yellows.All white paints darken or yellow over time, but the change is more evident with bright whites, such as General Finishes Snow White Milk Paint.Treat gently, and do not clean with commercial products during the curing period. Avoid placing heavy objects on surfaces that have not completely cured.

PATINA GREEN PAINT ENAMEL FULL

Water-based finishes cure and harden for full use after 21 days in ideal conditions. See 'Step 4: Topcoat over Milk Paint' below.

Topcoat is not required but is recommended in certain situations.

Remove dust with a vacuum, compressed air, an oil-free tack cloth or a water-dampened rag.

If you decide to re-coat before the recommended time, test dryness.

To accelerate dry time in humid conditions, add General Finishes Acceleratorand work in a space with good ventilation and air movement.

Oil over water: Let water-based products dry 24+hrs before applying oil-based products.

Water over oil: Let oil-based products dry 72+hrs before applying water-based products.

Layering General Finishes water- and oil-based products:.

Applying over products from other brands.

Applying over an existing sealed finish.

If in doubt, wait longer. Rushing dry time can cause clouding/blush in topcoat due to moisture trapped between coats. Increase dry time if: Finish sand between coats with a fine-grade (220-320) foam sanding sponge or 400-grit sandpaper to improve smoothness and adhesion.

Dry 2+ hours between coats and before gf water-based topcoat in ideal conditions: 70☏/20☌ 50-70% humidity. Be sure to allow adequate dry time. You can tell if a water-based finish is dry if it forms a powder when lightly sanded with a fine-grade (220-320) foam sanding pad.

Face frames on cabinets: Milk Paint can be applied successfully to cabinet face frames, edges or drawer fronts with a brush, pad or small cabinet-specific roller such as Whizz or AllPro brand.

Read here for more information on spraying techniques. Wear full filter NIOSH/MSHA-approved respiratory & eye protection. For narrow surfaces, reduce the fan pattern to 2-3' wide to reduce overspray. Overlap each pass 25% to conceal lines. On large, flat areas, use wet, even patterns 6-8' wide. See our general guide for spray tip sizes. Keep your gun at a 90° angle, 6-8' from the surface. HVLP: 1.8mm-2.0mm spray tip, medium air cap. Verify tip sizes with your equipment supplier. Before spraying, strain paint through a medium-mesh filter. Spray wet films at 3-5-mil thickness.

Spray application: See video tutorial on spraying Milk Paint.

Hand application: Using a synthetic bristle brush, foam brush, pad applicator, staining pad or microfiber roller such as Whizz or AllPro brand, apply using smooth, even strokes.

Apply as many coats as needed for desired coverage. 2-3 coats are standard but additional coats may be required when using colors with less 'hide properties,' such as bright reds, greens, yellows and whites.

GF assumes no liability for the improper use of these products. Increase open time, if needed, with up to 10-15% General Finishes Extender if allowed by local regulations. GF Extender will improve flow and leveling and increase open time, which is helpful in dry climates. California Residents: Adding more than 2% of GF Extender will make the products non-compliant per SCAQMD Regulations. This paint already contains a flow agent and outside products may not be compatible. Do not use flowing agents such as Floetrol. Thin as desired with distilled water start with 5%, adding up to 10% by volume.

Stir paint to reincorporate solids that have settled to the bottom of the can before and throughout the application process.

Substrate: Wood (See below for other substrates) General Finishes Milk Paint Application Steps

PATINA GREEN PAINT ENAMEL HOW TO

Watch our How To Achieve A Bright White Finish Here

Watch our Milk Paint Product Overview Video Here Darker colors can be top-coated if a higher sheen is desired. If you want a white paint with a higher sheen, use GF White Poly (spray only) or GF Brushable White Enamel instead.

GF Milk Paint is a premium self-sealing finish and does not require a topcoat. CAUTION: Do NOT use any type of clear topcoat over white or light GF Milk Paint Colors, as it may cause yellowing when used over wood substrates.

Patina green paint enamel